m |
(→Recommend radios for homebrew repeaters) |
||
Line 289: | Line 289: | ||
| {{check mark}} | | {{check mark}} | ||
| KC9FQT Works great, used for the WF1RES repeater, used with rear DB25 port | | KC9FQT Works great, used for the WF1RES repeater, used with rear DB25 port | ||
+ | |- | ||
+ | |||
+ | | TM-D710 | ||
+ | | {{cross mark}} | ||
+ | | {{cross mark}} | ||
+ | | 5B4AMD Does not work for DMR! PTT works but the handheld does not decode. RX does not work at all. DSTAR not yet tested. | ||
|- | |- | ||
![]() | |||
Homebrew MMDVM | |||
---|---|---|---|
Vendor | Homebrew | ||
Model | MMDVM | ||
Firmware | unspecified | ||
Website | https://github.com/g4klx/ | ||
Modes | |||
DMR | ![]() |
D-Star | ![]() |
Tetra | ![]() |
P25 | ![]() |
Terminal support | |||
Group call | ![]() |
Voice call | ![]() |
SMS | ![]() |
IP | ![]() |
GPS | ![]() |
ARS/RRS | ![]() |
DMR Protocol support | |||
Talker Alias | ![]() |
In call GPS | ![]() |
Blog: http://www.mmdvm.com/
Group: https://groups.yahoo.com/groups/mmdvm/
Sources: https://github.com/g4klx/
Configurer un MMDVM de A à Z: https://www.dropbox.com/s/k8761h40czy5x1s/Configurer%20un%20MMDVM%20de%20A%20%C3%A0%20Z%20.pdf?dl=0
[General] Callsign=R1ABC Timeout=180 Duplex=1 #ModeHang=10 RFModeHang=10 NetModeHang=4 Display=Nextion Daemon=0 [Info] RXFrequency=434000000 TXFrequency=439000000 Power=1 Latitude=51.0 Longitude=39.0 Height=10 (par rapport au sol) Location=JN25FF Description=Multi-Mode Repeater URL=www.dstar.su [Log] # Logging levels, 0=No logging DisplayLevel=1 FileLevel=1 FilePath=. FileRoot=MMDVM [CW Id] Enable=1 Time=10 [DMR Id Lookup] File=DMRIds.dat Time=24 [DMR] Enable=1 Id=250199 ColorCode=1 [DMR Network] Enable=1 Address=master.dstar.su Port=62031 Password=passw0rd Debug=1
Being tested on | ![]() |
---|---|
Unknown | ![]() |
Supported | ![]() |
Unsupported | ![]() |
Known to work well for DStar, all radios should also work fine for DMR (otherwise please edit this list). The following radios have been approved to work as homebrew repeaters HF frontends:
Motorola | |||
---|---|---|---|
Model | RX | TX | Notes |
CDM750 / 1250 / 1550LS | ![]() |
![]() |
Excellent TX & RX on all modes |
CM140 / 160 / 340 | ![]() |
![]() |
EM200(CM140) Very low BER at Rx (SV4QXF) Tx works (SQ6POG) |
EM400 | ![]() |
![]() |
-XE1HAX- TX / RX VHF good work with (SP8NTH) v0.04 |
GM1200 | ![]() |
![]() |
D-Star,DMR,C4FM,P25 - TX using PIN 24 ACC, RX only via PIN 5 of internal CS(Option)connector [DISC OUT]! PIN 25 ACC NOT WORKING! OK2IT see #GM1200 DISC out |
GM300/Maxtrac | ![]() |
![]() |
N3FE |
GM338 | ![]() |
![]() |
DMR & C4FM tested |
GM340 / GM360 / GM380 | ![]() |
![]() |
|
GM350 / GM950 | ![]() |
![]() |
PCB Mod. VHF RX TX work (SQ9MYX) |
GM600 | ![]() |
TX UHF Work (SQ9MYX) | |
GM600 (reprogrammed to GM950) | ![]() |
![]() |
TX / RX UHF Work excellent on SR8UWD (SP8NTH) |
GR1225 | ![]() |
![]() |
N9KRG |
M1225 | ![]() |
![]() |
Receive causing unstable BER at Rx 5~10% (VE2RI) |
MCS2000 | ![]() |
![]() |
Unstable BER at Rx 1,2~5% (SV4QXF) |
MSF5000 | ![]() |
![]() |
X74CXB7106AT Works well for DMR; C4FM and Dstar not tested (YO2LLQ) |
MTR2000 | ![]() |
![]() |
Very well for DMR and DStar - C4FM not tested (IZ5IGB) |
Pro 3100 | ![]() |
![]() |
At least with 4 used radios I tested, Tx is center frequency is unstable. |
Pro 5100 | ![]() |
![]() |
Excellent TX & RX on all modes |
R100 Repeater | ![]() |
![]() |
N1XBM |
VRM650 (MCS2000) | ![]() |
![]() |
K0XM/W0NQX |
VRM850 (MCS2000) | ![]() |
![]() |
N4IRS See VRM.zip in the Yahoo MMDVM files/Hardware area |
Kenwood | |||
Model | RX | TX | Notes |
TM-V71A/E | ![]() |
TX Has a timeout of Max 10 min and its impossible to change this. | |
TH-F7E | ![]() |
![]() |
(CT1HDC) (IW9GRL - Good reception but unstable BER 0.3~5% ) |
TKR-750 | ![]() |
![]() |
VK4JLM Tested DSTAR and DMR, interfaced via rear DB25 |
TKR-830 | ![]() |
![]() |
N4IRS Good receive and transmit Tested DMR only Needs internal jumper Doc to follow |
TKR-850 | ![]() |
![]() |
VK4JLM Tested DSTAR and DMR, interfaced via rear DB25 |
TK-8180 | ![]() |
![]() |
KC9FQT Works great, used for the WF1RES repeater, used with rear DB25 port |
TM-D710 | ![]() |
![]() |
5B4AMD Does not work for DMR! PTT works but the handheld does not decode. RX does not work at all. DSTAR not yet tested. |
YAESU | |||
Model | RX | TX | Notes |
DR-1X | ![]() |
![]() |
TX/RX audio is excellent, DMR/D-Star Tested (W2GLD) |
FT-7900 | ![]() |
![]() |
Check/fine tune frequency for DMR use. TX will sag with temperature, set it 2-300 Hz above. (LA1PHA/LA1FTA) |
FT-7800 | ![]() |
![]() |
Check/fine tune frequency for DMR use. TX will sag with temperature, set it 2-300 Hz above. (LA1PHA/LA1FTA) |
FT-8800 | ![]() |
![]() |
|
FT-100D | ![]() |
(CT1HDC) | |
FT-8900 | ![]() |
![]() |
(DMR CT1JIB) |
FT-817 | ![]() |
![]() |
RX also looks to work (PD0ZRY) |
FT-857 | ![]() |
![]() |
DMR/DSTAR works very well as DMO mode, BER stable around 1-2% ( IW9HFS ) |
FTM100/DE | ![]() |
![]() |
PinOut MMDVM-->MINIDIN 10PIN : 1=DIN6, 2=DIN4, 3=DIN2, 5=DIN1, 6=DIN3 - IZ0RIN |
VXR-9000 UHF | ![]() |
![]() |
DMR/DSTAR works very well as DMO mode, TXDelay=45, DMRDelay=27, TXInvert=1, RXInvert=0 (F4GIX) |
HYT | |||
Model | RX | TX | Notes |
TM-600U | ![]() |
![]() |
RX work perfect. TX not work! (SQ9MYX) |
Tait | |||
Model | RX | TX | Notes |
T800 Series I | ![]() |
![]() |
For TX bypass/cut off low pass filter stage in audio processor, provide new DC bias at half rail into buffer, inject data at buffer. For RX tap at or near discriminator. (VK2AMV) |
T800 Series II | ![]() |
![]() |
N4IRS See Tait Series II data modifications.zip in the Yahoo MMDVM files/Hardware area. Additional note by VK2AMV, Be very careful of DC leakage into buffer effecting Op Amp DC bias. I had huge problems with less than a Microamp of DC leakage through a faulty DC blocking capacitor before I discovered it. DMR works great with T800 SII. |
T2020 Series II | ![]() |
![]() |
DMR Works, More info (F4GIX) |
Tm8100 | ![]() |
![]() |
DMR/DSTAR works well as DMO mode,DMR Delay 83 , More info (F4GIX) |
Tm8250 | ![]() |
![]() |
DMR/DSTAR works well as DMO mode,DMR Delay 83 , More info (F4GIX) |
TB7100 | ![]() |
![]() |
works with internal connections to RX/TX DF2ET, see https://www.florian-wolters.de/blog/2017/04/02/interfacing-tait-tb7100-and-mmdvm/ |
ICOM | |||
Model | RX | TX | Notes |
IC E880 | ![]() |
![]() |
DMR/DSTAR works well as DMO mode (IK5XMK) |
IC-V200TRE | ![]() |
![]() |
DMR/DSTAR works, DMR Delay=40, More info (F4GIX) |
IC-E2820 | ![]() |
![]() |
DMR works very well as DMO mode (SY1BRU) |
IC-7000 | ![]() |
![]() |
DMR/D-Star works very well as DMO mode (SV6NOB) https://www.youtube.com/watch?v=NevkCvcxZYo |
Harris | |||
Model | RX | TX | Notes |
MASTR III | ![]() |
![]() |
DMR works well (NF0T) |
Maxon | |||
Model | RX | TX | Notes |
SM-6450U | ![]() |
![]() |
RX works great / TX unstable(YO6NAM) |
Bridgecom | |||
Model | RX | TX | Notes |
BCR-50x | ![]() |
![]() |
All modes work well (KØXM) |
Internal CS option connector of a Motorola GM1200 with discriminator on pin 5. Complete pinout at http://www.batlabs.com/gm900.html
![]() | |||
Homebrew MMDVM | |||
---|---|---|---|
Vendor | Homebrew | ||
Model | MMDVM | ||
Firmware | unspecified | ||
Website | https://github.com/g4klx/ | ||
Modes | |||
DMR | ![]() |
D-Star | ![]() |
Tetra | ![]() |
P25 | ![]() |
Terminal support | |||
Group call | ![]() |
Voice call | ![]() |
SMS | ![]() |
IP | ![]() |
GPS | ![]() |
ARS/RRS | ![]() |
DMR Protocol support | |||
Talker Alias | ![]() |
In call GPS | ![]() |
Blog: http://www.mmdvm.com/
Group: https://groups.yahoo.com/groups/mmdvm/
Sources: https://github.com/g4klx/
Configurer un MMDVM de A à Z: https://www.dropbox.com/s/k8761h40czy5x1s/Configurer%20un%20MMDVM%20de%20A%20%C3%A0%20Z%20.pdf?dl=0
[General] Callsign=R1ABC Timeout=180 Duplex=1 #ModeHang=10 RFModeHang=10 NetModeHang=4 Display=Nextion Daemon=0 [Info] RXFrequency=434000000 TXFrequency=439000000 Power=1 Latitude=51.0 Longitude=39.0 Height=10 (par rapport au sol) Location=JN25FF Description=Multi-Mode Repeater URL=www.dstar.su [Log] # Logging levels, 0=No logging DisplayLevel=1 FileLevel=1 FilePath=. FileRoot=MMDVM [CW Id] Enable=1 Time=10 [DMR Id Lookup] File=DMRIds.dat Time=24 [DMR] Enable=1 Id=250199 ColorCode=1 [DMR Network] Enable=1 Address=master.dstar.su Port=62031 Password=passw0rd Debug=1
Being tested on | ![]() |
---|---|
Unknown | ![]() |
Supported | ![]() |
Unsupported | ![]() |
Known to work well for DStar, all radios should also work fine for DMR (otherwise please edit this list). The following radios have been approved to work as homebrew repeaters HF frontends:
Motorola | |||
---|---|---|---|
Model | RX | TX | Notes |
CDM750 / 1250 / 1550LS | ![]() |
![]() |
Excellent TX & RX on all modes |
CM140 / 160 / 340 | ![]() |
![]() |
EM200(CM140) Very low BER at Rx (SV4QXF) Tx works (SQ6POG) |
EM400 | ![]() |
![]() |
-XE1HAX- TX / RX VHF good work with (SP8NTH) v0.04 |
GM1200 | ![]() |
![]() |
D-Star,DMR,C4FM,P25 - TX using PIN 24 ACC, RX only via PIN 5 of internal CS(Option)connector [DISC OUT]! PIN 25 ACC NOT WORKING! OK2IT see #GM1200 DISC out |
GM300/Maxtrac | ![]() |
![]() |
N3FE |
GM338 | ![]() |
![]() |
DMR & C4FM tested |
GM340 / GM360 / GM380 | ![]() |
![]() |
|
GM350 / GM950 | ![]() |
![]() |
PCB Mod. VHF RX TX work (SQ9MYX) |
GM600 | ![]() |
TX UHF Work (SQ9MYX) | |
GM600 (reprogrammed to GM950) | ![]() |
![]() |
TX / RX UHF Work excellent on SR8UWD (SP8NTH) |
GR1225 | ![]() |
![]() |
N9KRG |
M1225 | ![]() |
![]() |
Receive causing unstable BER at Rx 5~10% (VE2RI) |
MCS2000 | ![]() |
![]() |
Unstable BER at Rx 1,2~5% (SV4QXF) |
MSF5000 | ![]() |
![]() |
X74CXB7106AT Works well for DMR; C4FM and Dstar not tested (YO2LLQ) |
MTR2000 | ![]() |
![]() |
Very well for DMR and DStar - C4FM not tested (IZ5IGB) |
Pro 3100 | ![]() |
![]() |
At least with 4 used radios I tested, Tx is center frequency is unstable. |
Pro 5100 | ![]() |
![]() |
Excellent TX & RX on all modes |
R100 Repeater | ![]() |
![]() |
N1XBM |
VRM650 (MCS2000) | ![]() |
![]() |
K0XM/W0NQX |
VRM850 (MCS2000) | ![]() |
![]() |
N4IRS See VRM.zip in the Yahoo MMDVM files/Hardware area |
Kenwood | |||
Model | RX | TX | Notes |
TM-V71A/E | ![]() |
TX Has a timeout of Max 10 min and its impossible to change this. | |
TH-F7E | ![]() |
![]() |
(CT1HDC) (IW9GRL - Good reception but unstable BER 0.3~5% ) |
TKR-750 | ![]() |
![]() |
VK4JLM Tested DSTAR and DMR, interfaced via rear DB25 |
TKR-830 | ![]() |
![]() |
N4IRS Good receive and transmit Tested DMR only Needs internal jumper Doc to follow |
TKR-850 | ![]() |
![]() |
VK4JLM Tested DSTAR and DMR, interfaced via rear DB25 |
TK-8180 | ![]() |
![]() |
KC9FQT Works great, used for the WF1RES repeater, used with rear DB25 port |
YAESU | |||
Model | RX | TX | Notes |
DR-1X | ![]() |
![]() |
TX/RX audio is excellent, DMR/D-Star Tested (W2GLD) |
FT-7900 | ![]() |
![]() |
Check/fine tune frequency for DMR use. TX will sag with temperature, set it 2-300 Hz above. (LA1PHA/LA1FTA) |
FT-7800 | ![]() |
![]() |
Check/fine tune frequency for DMR use. TX will sag with temperature, set it 2-300 Hz above. (LA1PHA/LA1FTA) |
FT-8800 | ![]() |
![]() |
|
FT-100D | ![]() |
(CT1HDC) | |
FT-8900 | ![]() |
![]() |
(DMR CT1JIB) |
FT-817 | ![]() |
![]() |
RX also looks to work (PD0ZRY) |
FT-857 | ![]() |
![]() |
DMR/DSTAR works very well as DMO mode, BER stable around 1-2% ( IW9HFS ) |
FTM100/DE | ![]() |
![]() |
PinOut MMDVM-->MINIDIN 10PIN : 1=DIN6, 2=DIN4, 3=DIN2, 5=DIN1, 6=DIN3 - IZ0RIN |
VXR-9000 UHF | ![]() |
![]() |
DMR/DSTAR works very well as DMO mode, TXDelay=45, DMRDelay=27, TXInvert=1, RXInvert=0 (F4GIX) |
HYT | |||
Model | RX | TX | Notes |
TM-600U | ![]() |
![]() |
RX work perfect. TX not work! (SQ9MYX) |
Tait | |||
Model | RX | TX | Notes |
T800 Series I | ![]() |
![]() |
For TX bypass/cut off low pass filter stage in audio processor, provide new DC bias at half rail into buffer, inject data at buffer. For RX tap at or near discriminator. (VK2AMV) |
T800 Series II | ![]() |
![]() |
N4IRS See Tait Series II data modifications.zip in the Yahoo MMDVM files/Hardware area. Additional note by VK2AMV, Be very careful of DC leakage into buffer effecting Op Amp DC bias. I had huge problems with less than a Microamp of DC leakage through a faulty DC blocking capacitor before I discovered it. DMR works great with T800 SII. |
T2020 Series II | ![]() |
![]() |
DMR Works, More info (F4GIX) |
Tm8100 | ![]() |
![]() |
DMR/DSTAR works well as DMO mode,DMR Delay 83 , More info (F4GIX) |
Tm8250 | ![]() |
![]() |
DMR/DSTAR works well as DMO mode,DMR Delay 83 , More info (F4GIX) |
TB7100 | ![]() |
![]() |
works with internal connections to RX/TX DF2ET, see https://www.florian-wolters.de/blog/2017/04/02/interfacing-tait-tb7100-and-mmdvm/ |
ICOM | |||
Model | RX | TX | Notes |
IC E880 | ![]() |
![]() |
DMR/DSTAR works well as DMO mode (IK5XMK) |
IC-V200TRE | ![]() |
![]() |
DMR/DSTAR works, DMR Delay=40, More info (F4GIX) |
IC-E2820 | ![]() |
![]() |
DMR works very well as DMO mode (SY1BRU) |
IC-7000 | ![]() |
![]() |
DMR/D-Star works very well as DMO mode (SV6NOB) https://www.youtube.com/watch?v=NevkCvcxZYo |
Harris | |||
Model | RX | TX | Notes |
MASTR III | ![]() |
![]() |
DMR works well (NF0T) |
Maxon | |||
Model | RX | TX | Notes |
SM-6450U | ![]() |
![]() |
RX works great / TX unstable(YO6NAM) |
Bridgecom | |||
Model | RX | TX | Notes |
BCR-50x | ![]() |
![]() |
All modes work well (KØXM) |
Internal CS option connector of a Motorola GM1200 with discriminator on pin 5. Complete pinout at http://www.batlabs.com/gm900.html